View BD37513FS_9053663.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

product structure silicon monolithic integrated circuit this product has no designed protection against radioactive rays 1/ 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. tsz22111 ? 14 ? 001 www.rohm.com 16.dec.2015 rev.001 sound processor with built - in 2 - band equalizer BD37513FS general description BD37513FS is a sound processor with built - in 2 - band equalizer for car audio. the functions are 4ch stereo input selector, input - gain c ontrol, main volume, loudness, and 4 ch fad er volume. moreover, its advanced switch circuit, which is an original rohm technology, can reduce various switching noise (ex. no - signal, low frequency like 20hz & large signal inputs). advanced switch makes control of microcomputer easier, supporting the construct ion of a high quality car audio system. features ? reduce switching noise of input gain control, mute, main volume, fader volume, bass, treble, loudness by using advanced switch circuit . ? built - in 1 differential input selector and 3 single -en ded input selectors ? built - in ground isolation amplifier inputs, ideal for external stereo input. ? built - in input gain controller reduces switching noise for volume of a portable audio input. ? decrease the number of external components due to built - in 2 - band equalizer filter and loudness filter . also , it is possible to control gv using i 2 c bus control. ? it is possible to adjust the gain of the bass and treble up to 20db with 1 db step gain adjustment. ? energy - saving design resulting in l ow current consumption, by utilizing the bi - cmos process . it has the advantage in quality over scaling down the power heat control of the internal regulators. ? input terminals and output terminals are organized and separately laid out to keep the signal flow in one direction whi ch results in simpler and smaller pcb layout. ? it is possible to control the i 2 c bus by 3.3v/5v. key specifications ? power supply voltage range : 7.0v to 9.5v ? circuit current ( no signal ): 38ma( typ ) ? total harmonic distortion 1 : 0.001%( typ ) ? maximum i nput voltage : 2.3vrms( typ ) ? cross - talk between selectors : - 100db( typ ) ? volume control range : +15db to - 79db ? output noise voltage 1 : 3.8vrms( typ ) ? residual output noise voltage : 1.8vrms( typ ) ? operating temperature range : -40 c to +85 c package w (typ) x d(typ) x h(max) applications it is optimal for use in car audio systems . it can also be use d for audio equipment of mini compo, micro compo, tv , etc. ssop - a20 8.70mm x 7.80 mm x 2.01mm datashee t datashee t
BD37513FS 2 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 typical application circuit pin configuration pin description s pin no. pin name description pin no. pin name description 1 fil vcc/2 terminal 11 mute external compulsory mute terminal 2 a1 a input terminal of 1ch 12 test1 test pin 3 a2 a input terminal of 2ch 13 outr2 rear output terminal of 2ch 4 b1 b input terminal of 1ch 14 outr1 rear output terminal of 1ch 5 b2 b input terminal of 2ch 15 outf2 front output terminal of 2ch 6 c1 c input terminal of 1ch 16 outf1 front output terminal of 1ch 7 c2 c inp ut terminal of 2ch 17 vcc power supply terminal 8 dp1 d positive input terminal of 1ch 18 scl i 2 c communication clock terminal 9 dn d negative input terminal 19 sda i 2 c communication data terminal 10 dp2 d positive input terminal of 2ch 20 gnd gnd termi nal unit 5> @ c : [f] BD37513FS top view fil 1 a1 2 a2 3 b1 4 b2 5 c1 6 c2 7 dp1 8 dn 9 dp2 10 11 mute 12 test 1 13 outr 2 14 outr 1 15 outf2 16 outf1 17 vcc 18 scl 19 sda 20 gnd
BD37513FS 3 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 block diagram gain: 0db to - 79db/1db step 20db to 0db/ 1d b step gain:+20d b to - 20 db/1db gain+15d b to - 79d b/1db step gain:+20d b to 0db/1 db step gnd iso amp input selector ( 3 single - end and 1 stereo iso ) volume / mute 2 band eq ( tone control ) loudness i 2 c bus logic gnd 100 k vcc / 2 input gain 20 19 18 17 16 15 14 13 12 11 f a d e r 1 2 3 4 5 6 7 8 9 10 100 k 100 k 100 k 250 k 250 k 250 k 250 k gnd iso amp 250 k f a d e r f a d e r f a d e r vcc fader gain : 0 db - 79 b / 1 db step loudness 20 db 0 b / 1 b step ? 0 = 800 ? hicut 1 / 2 / 3 / 4 2 band eq ( tone control ) gain + 20 db - 20 db / 1 db ? bass f 0 = 100 hz , q = 1 . 0 ? treble f 0 = 10 khz q = 1 . 25 volume gain :+ 15 db - 79 db / 1 db step input gain gain :+ 20 db 0 db / 1 db step
BD37513FS 4 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 absolute maximum ratings (ta=25 c ) (note) this value derates by 7.5mw/ c for ta=25 c or more when rohm standard board is used. thermal res lvwdqfhmd .3 ( c /w) rohm standard board size : 70 x 70 x 1.6( mm 3 ) material : a fr4 grass epoxy board(3% or less of copper foil area) caution : operating the ic over the absolute maximum ratings may damage the ic. the damage can either be a short circu it between pins or an open circuit between pins and the internal circuitry. therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the ic is operated over the absolute maximum ratings . recommended operating cond ition s parameter symbol min typ max unit power supply voltage v cc 7.0 - 9.5 v temperature topr - 40 - +85 v electrical characteristics (unless specified otherwise , ta=25 c , v cc =8.5v, f=1khz, v in 9upv5j 5 l n $lqsxw,qsxwjdlqg% mute off , volume 0db, tone control 0db, loudness 0db, fader 0db) block parameter symbol limit unit conditions min typ max general circuit current i q
BD37513FS 5 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 electrical characteristics - continued (unless specified otherwise , ta=25 c , v cc =8.5v, f=1khz, v in 9upv5j 5 l n $lqsxw,qsxwjdlqg% mute off , volume 0db, tone control 0db, loudness 0db, fader 0db) block parameter symbol limit unit conditions min typ max mute mute attenuation
BD37513FS 6 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 thd+n [%] output voltage : v out [vrms] 10khz 1khz 100hz typical performance curves frequency [hz] gain [db] bass gain : - 20db to +20db /1db step fo : 60hz q : 0.5 figure 2 . total harmonic distortion vs output voltage figure 3 . gain v s freq uency figure 4 . bass gai n vs freq uency figure 1 . quiescent current vs su pply voltage supply voltage : v cc [v] quiescent cur rent : i q [ma] v in [vrms] gain [db] frequency [hz] - 5 - 4 - 3 - 2 - 1 0 1 2 3 4 5 10 100 1k 10k 100k frequency (hz) gain (db) gain=0db 0.001 0.01 0.1 1 10 0.001 0.01 0.1 1 10 vout (v) thd+n (%) 0.001 0.01 0.1 1 10 vout - 25 - 20 - 15 - 10 - 5 0 5 10 15 20 25 10 100 1k 10k 100k 0 10 20 30 40 50 0 2 4 6 8 10 vcc[v] iq[ma]
BD37513FS 7 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 typical performance curves - continued treble gain [db] figure 7 . output noise vs bass gain bass gain [db] output noise [ vrms] figure 8 . output noise vs treble gain output noise [ vrms] figure 1 10 100 1000 -20 -15 -10 -5 0 5 10 15 20 bass gain [db] j?R [uvrms] din-audio ihf-a 1 10 100 1000 -20 -15 -10 -5 0 5 10 15 20 treble gain [db] j?R [uvrms] din-audio ihf-a - 25 - 20 - 15 - 10 - 5 0 5 10 15 20 25 10 1k 100k gain (db) frequency (hz) 1 10 100 1000 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 volume gain[db] j?R[uvrms] din-audio ihf-a
BD37513FS 8 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 typical performance curve s - continued figure 11 . advanced switch 1 figure 12 . advanced switch 2 figure 9 . cmrr vs fr eq uency gain [db] frequency [h z ] figure 10 . o utput voltage vs r load output voltage : v out [vrms] r load [ohm] 0.0 0.5 1.0 1.5 2.0 2.5 100 1000 10000 100000 ?[ohm] [vrms] -70 -60 -50 -40 -30 -20 -10 0 10 100 1k 10k 100k frequency (hz) gain (db)
BD37513FS 9 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 timing chart control signal specification (1) electrical specifications and timing for bus lines and i/o stage fig ure 13 . i 2 c - bus signal timing diagram ta ble 1 characteristics of the sda and scl bus lines for i 2 c - bus devices parameter symbol fast - mode i 2 c - bus unit min max 1 scl clock frequency f scl 0 400 khz 2 bus free time between a stop and start condition t buf 1.3 buf 4 us hd ; sta 2 us hd ; dat 1 us low 3 us high 1 us su ; dat 1 us su ; sto 2 us scl clock frequency 250 khz scl sda sda s scl t low t r t hd;dat p t hd;sta t high t buf t f t su;dat t su;stat t su;stot t sp t hd;stat sr p
BD37513FS 10 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 (2) i 2 c bus format msb lsb msb lsb msb lsb s slave address a select address a data a p 1bit 8bit 1bit 8bit 1bit 8bit 1bit 1bit s = start condition (recognition of start bit) slave address = recognition of slave address. the first 7 bits correspond to the slave address . the least significant bit is 3 l which corresponds to write mode . a = acknowledge bit (recognition of acknowledgement) select address = select address corresponding to volume, bass or treble. data = data on every volume and tone. p = stop condition (recognition of stop bit) (3) i 2 c bus interface protocol (a) basic form at s slav e address a select address a data a p msb lsb msb lsb msb lsb (b) automatic increment (select address increases (+1) according to the number of data. ) s slave address a select address a data1 a data2 a ???? msb lsb msb lsb msb lsb msb lsb ( example ) q data1 shall be set as data of address specified by select address. r data2 shall be set as data of address specified by select address +1. s datan shall be set as data of address speci fied by select address +n - 1. (c) configuration unavailable for transmission (in this case, only select address1 is set. ) s slave address a select address1 a data a select address 2 a data a p msb lsb msb lsb msb lsb msb l sb msb lsb
BD37513FS 11 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 (5) select address & data items select address (hex) msb data lsb d7 d6 d5 d4 d3 d2 d1 d0 initial setup 1 01 advanced switch on/off 0 advanced switch time of input gain/volume tone/fader/loudness 0 0 advanced switch time of mute initial setup 2 02 0 0 0 0 0 0 0 0 initial setup 3 03 0 0 0 1 0 0 0 1 input selector 05 0 0 0 input selector input gain 06 mute on/off 0 0 input gain volume gain 20 volume gain / attenuation fader 1ch front 28 fader attenuation fader 2ch front 29 fader attenuation fader 1ch rear 2a fader attenuation fader 2ch rear 2b fader attenuation test mode 1 2c 1 1 1 1 1 1 1 1 test mode 2 41 0 0 1 0 0 0 0 1 test mode 3 44 0 0 0 0 0 0 0 0 test mode 4 47 0 0 0 1 0 0 0 1 bass gain 51 bass boost/ cut 0 0 bass gain test mode 5 54 1 0 0 0 0 0 0 0 treble gain 57 treble boost/ cut 0 0 treble gain loudness gain 75 0 loudness hicut loudness gain system reset fe 1 0 0 0 0 0 0 1 advanced switch note 1. the advanced switch works in the latch part while changing from one function to another. 2. upon continuous data transfer, the select address rolls over because of the automatic increment function, as shown below. 3. for the function of i nput s elector etc, a dvanced s witch is not used . therefore, please apply mute on the set side w hen chang ing these setting s . 4. when using mute function of this ic at the time of changing input selector, please switch mute on/off while waiting for advanced - mute time. 41 44 47 51 54 57 7 5 01 02 03 05 06 20 28 29 2a 2b 2c
BD37513FS 12 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 sele ct address 01 (hex) time msb advanced switch time of mute lsb d7 d6 d5 d4 d3 d 2 d1 d0 0.6msec advanced switch on/off 0 advanced switch time of input gain/volume tone/fader/loudness 0 0 0 0 1.0msec 0 1 1.4msec 1 0 3.2msec 1 1 time msb advanced switch time of input gain/volume/tone/fader/loudness lsb d7 d6 d5 d4 d3 d2 d1 d0 4.7 msec advanced switch on/off 0 0 0 0 0 advanced switch time of mute 7.1 msec 0 1 11.2 msec 1 0 14.4 msec 1 1 mode msb advanced switch on/off lsb d7 d6 d5 d4 d3 d2 d1 d0 off 0 0 advanced switch time of input gain/vo lume tone/fader/loudness 0 0 advanced switch time of mute on 1 select address 05(hex) mode msb input selector lsb d7 d6 d5 d4 d3 d2 d1 d0 initial 0 0 0 0 0 0 0 0 a 0 0 0 1 b 0 0 1 0 c 0 0 1 1 d diff 0 1 1 1 input short 1 0 0 1 prohibition other setting input short : 7khlqsxwlpshgdqfhrihdfklqsxwwhuplqdolvorzhuhgiurpn 7<3wrn 7<3 (for quick charge of coupling capacitor) : initial condition
BD37513FS 13 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 select address 06 (hex) gain msb input gain lsb d7 d6 d5 d4 d3 d2 d1 d0 0db mute on/off 0 0 0 0 0 0 0 1db 0 0 0 0 1 2db 0 0 0 1 0 3db 0 0 0 1 1 4db 0 0 1 0 0 5db 0 0 1 0 1 6db 0 0 1 1 0 7db 0 0 1 1 1 8db 0 1 0 0 0 9db 0 1 0 0 1 10db 0 1 0 1 0 11db 0 1 0 1 1 12db 0 1 1 0 0 13db 0 1 1 0 1 14db 0 1 1 1 0 15db 0 1 1 1 1 16db 1 0 0 0 0 17db 1 0 0 0 1 18db 1 0 0 1 0 19db 1 0 0 1 1 20db 1 0 1 0 0 prohibition 1 1 0 1 1
BD37513FS 14 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 select address 51, 57 (hex) gain msb bass/ treble gain lsb d7 d6 d5 d4 d3 d2 d1 d0 0db bass/ treble boost /cut 0 0 0 0 0 0 0 1db 0 0 0 0 1 2db 0 0 0 1 0 3db 0 0 0 1 1 4db 0 0 1 0 0 5db 0 0 1 0 1 6db 0 0 1 1 0 7db 0 0 1 1 1 8db 0 1 0 0 0 9db 0 1 0 0 1 10db 0 1 0 1 0 11db 0 1 0 1 1 12db 0 1 1 0 0 13db 0 1 1 0 1 14db 0 1 1 1 0 15db 0 1 1 1 1 16db 1 0 0 0 0 17db 1 0 0 0 1 18db 1 0 0 1 0 19db 1 0 0 1 1 20db 1 0 1 0 0 prohibition 1 0 1 0 1
BD37513FS 15 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 select address 75 (hex) mode msb loudness hicut lsb d7 d6 d5 d4 d3 d2 d1 d0 hicu t1 0 0 0 loudness gain hicut2 0 1 hicut3 1 0 hicut4 1 1 gain msb loudness gain lsb d7 d6 d5 d4 d3 d2 d1 d0 0db 0 loudness hicut 0 0 0 0 0 1db 0 0 0 0 1 2db 0 0 0 1 0 3db 0 0 0 1 1 4db 0 0 1 0 0 5db 0 0 1 0 1 6db 0 0 1 1 0 7 db 0 0 1 1 1 8db 0 1 0 0 0 9db 0 1 0 0 1 10db 0 1 0 1 0 11db 0 1 0 1 1 12db 0 1 1 0 0 13db 0 1 1 0 1 14db 0 1 1 1 0 15db 0 1 1 1 1 16db 1 0 0 0 0 17db 1 0 0 0 1 18db 1 0 0 1 0 19db 1 0 0 1 1 20db 1 0 1 0 0 prohibit ion 1 0 1 0 1
BD37513FS 16 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 application informatio n 1. function and specifications function specifications input selector stereo 3 input differential 1 input input gain +20 db to 0db ( 1db step ) 3rvvleohwrxvh3$gydqfhgvzlwfkirusuhyhqwlrqrivzlwfklqjqrlvh mute 3rvvleohwrxvh3$gydqfhgvzlwfkirusuhyhqwlrqrivzlwfklqjqrlvh volume +15db to - 7 9db ( 1db step ) , - ?g% 3rvvleohwrxvh3$gydqfhgvzlwfkirusuhyhqwlrqrivzlwfklqjqrlvh bass +20 db to - 20db ( 1db step ) 3rvvleohwrxvh3$gydqfhgvzlwfkdwfkdqjlqjjdlq q=1 fo=100hz treble +20 db to - 20db ( 1db step ) 3rvvleohwrxvh3$gydqfhg vzlwfkdwfkdqjlqjjdlq q=1.25 fo=10khz fader 0db to - 79db, - ?g% 3rvvleohwrxvh3$gydqfhgvzlwfkirusuhyhqwlrqrivzlwfklqjqrlvh loudness 20db to 0db (1db step) fo=800hz 3rvvleohwrxvh3$gydqfhgvzlwfkirusuhyhqwlrqrivzlwfklqjqrlvh
BD37513FS 17 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 2. volume / fader volume attenuation data (db) d7 d6 d5 d4 d3 d2 d1 d0 (db) d7 d6 d5 d4 d3 d2 d1 d0 +15 0 1 1 1 0 0 0 1 - 33 1 0 1 0 0 0 0 1 +14 0 1 1 1 0 0 1 0 - 34 1 0 1 0 0 0 1 0 +13 0 1 1 1 0 0 1 1 - 35 1 0 1 0 0 0 1 1 +12 0 1 1 1 0 1 0 0 - 36 1 0 1 0 0 1 0 0 +11 0 1 1 1 0 1 0 1 - 37 1 0 1 0 0 1 0 1 +10 0 1 1 1 0 1 1 0 - 38 1 0 1 0 0 1 1 0 +9 0 1 1 1 0 1 1 1 - 39 1 0 1 0 0 1 1 1 +8 0 1 1 1 1 0 0 0 - 40 1 0 1 0 1 0 0 0 +7 0 1 1 1 1 0 0 1 - 41 1 0 1 0 1 0 0 1 +6 0 1 1 1 1 0 1 0 - 42 1 0 1 0 1 0 1 0 +5 0 1 1 1 1 0 1 1 - 43 1 0 1 0 1 0 1 1 +4 0 1 1 1 1 1 0 0 - 44 1 0 1 0 1 1 0 0 +3 0 1 1 1 1 1 0 1 - 45 1 0 1 0 1 1 0 1 +2 0 1 1 1 1 1 1 0 - 46 1 0 1 0 1 1 1 0 +1 0 1 1 1 1 1 1 1 - 47 1 0 1 0 1 1 1 1 0 1 0 0 0 0 0 0 0 - 48 1 0 1 1 0 0 0 0 - 1 1 0 0 0 0 0 0 1 - 49 1 0 1 1 0 0 0 1 - 2 1 0 0 0 0 0 1 0 - 50 1 0 1 1 0 0 1 0 - 3 1 0 0 0 0 0 1 1 - 51 1 0 1 1 0 0 1 1 - 4 1 0 0 0 0 1 0 0 - 52 1 0 1 1 0 1 0 0 - 5 1 0 0 0 0 1 0 1 - 53 1 0 1 1 0 1 0 1 - 6 1 0 0 0 0 1 1 0 - 54 1 0 1 1 0 1 1 0 - 7 1 0 0 0 0 1 1 1 - 55 1 0 1 1 0 1 1 1 - 8 1 0 0 0 1 0 0 0 - 56 1 0 1 1 1 0 0 0 - 9 1 0 0 0 1 0 0 1 - 57 1 0 1 1 1 0 0 1 - 10 1 0 0 0 1 0 1 0 - 58 1 0 1 1 1 0 1 0 - 11 1 0 0 0 1 0 1 1 - 59 1 0 1 1 1 0 1 1 - 12 1 0 0 0 1 1 0 0 - 60 1 0 1 1 1 1 0 0 - 13 1 0 0 0 1 1 0 1 - 61 1 0 1 1 1 1 0 1 - 14 1 0 0 0 1 1 1 0 - 62 1 0 1 1 1 1 1 0 - 15 1 0 0 0 1 1 1 1 - 63 1 0 1 1 1 1 1 1 - 16 1 0 0 1 0 0 0 0 - 64 1 1 0 0 0 0 0 0 - 17 1 0 0 1 0 0 0 1 - 65 1 1 0 0 0 0 0 1 - 18 1 0 0 1 0 0 1 0 - 66 1 1 0 0 0 0 1 0 - 19 1 0 0 1 0 0 1 1 - 67 1 1 0 0 0 0 1 1 - 20 1 0 0 1 0 1 0 0 - 68 1 1 0 0 0 1 0 0 - 21 1 0 0 1 0 1 0 1 - 69 1 1 0 0 0 1 0 1 - 22 1 0 0 1 0 1 1 0 - 70 1 1 0 0 0 1 1 0 - 23 1 0 0 1 0 1 1 1 - 71 1 1 0 0 0 1 1 1 - 24 1 0 0 1 1 0 0 0 - 72 1 1 0 0 1 0 0 0 - 25 1 0 0 1 1 0 0 1 - 73 1 1 0 0 1 0 0 1 - 26 1 0 0 1 1 0 1 0 - 74 1 1 0 0 1 0 1 0 - 27 1 0 0 1 1 0 1 1 - 75 1 1 0 0 1 0 1 1 - 28 1 0 0 1 1 1 0 0 - 76 1 1 0 0 1 1 0 0 - 29 1 0 0 1 1 1 0 1 - 77 1 1 0 0 1 1 0 1 - 30 1 0 0 1 1 1 1 0 - 78 1 1 0 0 1 1 1 0 - 31 1 0 0 1 1 1 1 1 - 79 1 1 0 0 1 1 1 1 - 32 1 0 1 0 0 0 0 0 - ? 1 1 1 1 1 1 1 1 for fader volume , only 0db to - ?g%duhdydlodeoh
BD37513FS 18 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 3. application circuit notes on wiring q please connect the decoupling capacitor of the power supply in the shortest po ssible distance to gnd. r gnd lines should be one - point connected. s wiring pattern of digital should be away from that of a nalog unit and cross - talk should not be acceptable. t scl and sda lines of i 2 c bus should not be parallel if possible. the lines sh ould be shielded, if they are adjacent to each other. u a nalog input lines should not be parallel if possible. the lines should be shielded, if they are adjacent to each other. v about test pin ( pin 12 ), please leave it as open. unit 5> @ c : [f] gain: 0db to - 79 db/1db step 20db to 0d b/1db step gain:+20d b to - 2 0db/1db gain+15db to - 79 db/1db step gain:+20db to 0 db/1db step vcc mute 10 0 . 1 10 2 . 2 k outr 2 outr 1 outf 2 outf 1 single 1 single 2 single 3 gnd isoration gnd sda scl 10 10 10 2 . 2 2 . 2 2 . 2 2 . 2 2 . 2 2 . 2 2 . 2 10 2 . 2 gnd iso amp input selector ( 3 single - end and 1 stereo iso ) volume / mute 2 band eq ( tone control ) loudness i 2 c bus logic gnd 100 k vcc / 2 input gain 20 19 18 17 16 15 14 13 12 11 f a d e r 1 2 3 4 5 6 7 8 9 10 100 k 100 k 100 k 250 k 250 k 250 k 250 k gnd iso amp 250 k f a d e r f a d e r f a d e r vcc fader gain : 0 db - 79 b / 1 db step loudness 20 db 0 b / 1 b step ? 0 = 800 ? hicut 1 / 2 / 3 / 4 2 band eq ( tone control ) gain + 20 db - 20 db / 1 db ? bass f 0 = 100 hz , q = 1 . 0 ? treble f 0 = 10 khz q = 1 . 25 volume gain :+ 15 db - 79 db / 1 db step input gain gain :+ 20 db 0 db / 1 db step 10
BD37513FS 19 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 power d issipation about the t hermal des ign of the ic characteristics of an ic have a great deal to do with the temperature at which it is used, and exceeding absolute maximum ratings may degrade and destroy the device . careful consideration must be given to the heat of the ic from the two stand points of immediate damage and long - term reliability of operation. figure 15 . temperatur e derating curve power dissipation values vary according to the board on which the ic is mounted ( note) values are actual measurements and are not guaranteed. reference data ssop - a20 1.5 1.0 0.5 0.0 0 25 50 75 100 125 150 amb ient temperature : ta (c) power dissipation : pd (w) 0.94w md = 133.3 c /w 85 measurement condition: rohm standard board board size : 70 x 70 x 1.6( mm 3 ) material : a fr4 grass epoxy board (3% or less of copper foil area)
BD37513FS 20 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 i/o equivalent circuit s terminal no. terminal name terminal voltage equivalent circuit terminal description 2 3 4 5 a1 a2 b1 b2 4.25 a terminal for signal input. 7khlqsxwlpshgdqfhlvn w\s 6 7 c1 c2 4.25 a terminal for signal input. the input im shgdqfhlvn w\s 8 9 10 dp1 dn dp2 4.25 input terminal available to single/differential mode. 7khlqsxwlpshgdqfhlvn w\s 11 mute ? a terminal for external compulsory mute. if terminal voltage is high level, the mute is off . and if the terminal voltage is low level, the mute is on . 13 14 15 16 outr2 outr1 outf2 outf1 4.25 a terminal for fader and subwoofer output. values in the pin explanation and input/output equivalent circuit are reference values only and are not guaranteed. gnd v cc 250k vcc gnd 1.65v gnd vcc 100k v cc gnd gnd vcc 250 k
BD37513FS 21 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 i /o equivalen t circuit - continued terminal no. terminal name terminal voltage equivalent circuit terminal description 17 vcc 8.5 power supply terminal. 18 scl vcc gnd 1.65v vcc gnd 1.65v
BD37513FS 22 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 operational notes 1. reverse connection of power supply connecting the power supply in reverse polarity can damage the ic. take precautions against reverse polarity when connecting the power supply, such as mounting an ext huqdo glrgh ehwzhhq wkh srzhu vxsso\ dqg wkh ,&?v srzhu supply pins. 2. power supply lines design the pcb layout pattern to provide low impedance supply lines. separate the ground and supply lines of the digital and analog blocks to prevent noise in the grou nd and supply lines of the digital block from affecting the analog block. furthermore, connect a capacitor to ground at all power supply pins. consider the effect of temperature and aging on the capacitance value when using electrolytic capacitors. 3. ground voltage ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition. 4. ground wiring pattern when using both small - signal and large - current ground traces, the two ground traces should be routed separately but connected to a single ground at the reference point of the application board to avoid fluctuations in the small - signal ground caused by large currents. also ensure that the ground traces of external components do not cause variations on the ground volt age. the ground lines must be as short and thick as possible to reduce line impedance. 5. thermal consideration should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in deterioration of the properties of the chip. in case of exceeding this absolute maximum rating, increase the board size and copper area to prevent exceeding the pd rating. 6. recommended operating conditions these conditions represent a range within which the expected characteristics of the ic can be approximately obtained. the electrical characteristics are guaranteed under the conditions of each parameter. 7. inrush current when power is first supplied to the ic, it is possible that the internal logic may be unstable and inrush current may fl ow instantaneously due to the internal powering sequence and delays, especially if the ic has more than one power supply. therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing of connections. 8. operation under strong electromagnetic field operating the ic in the presence of a strong electromagnetic field may cause the ic to malfunction. 9. testing on application boards when testing the ic on an application board, connecting a capacitor directly t o a low - impedance output pin may vxemhfwwkh,&wrvwuhvv$ozd\vglvfkdujhfdsdflwruvfrpsohwho\diwhuhdfksurfhvvruvwhs7kh,&?vsrzhuvxsso\ should always be turned off completely before connecting or removing it from the test setup during the inspe ction process. to prevent damage from static discharge, ground the ic during assembly and use similar precautions during transport and storage. 10. inter - pin short and mounting errors ensure that the direction and position are correct when mounting the ic on the pcb. incorrect mounting may result in damaging the ic. avoid nearby pins being shorted to each other especially to ground, power supply and output pin. inter - pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and unintentional solder bridge deposited in between pins during assembly to name a few. 11. unused input pins input pins of an ic are often connected to the gate of a mos transistor. the gate has extremely high impedance and extremely low capac itance. if left unconnected, the electric field from the outside can easily charge it. the small charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause unexpected operation of the ic. so unl ess otherwise specified, unused input pins should be connected to the power supply or ground line.
BD37513FS 23 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 operation al notes C ? ? ? ? ? ? ? ? ? ? ? n n p + p n n p + p s u b s t r a t e g n d n p + n n p + n p p s u b s t r a t e g n d g n d p a r a s i t i c e l e m e n t s p i n a p i n a p i n b p i n b b c e p a r a s i t i c e l e m e n t s g n d p a r a s i t i c e l e m e n t s c b e t r a n s i s t o r ( n p n ) r e s i s t o r n r e g i o n c l o s e - b y p a r a s i t i c e l e m e n t s
BD37513FS 24 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 ordering informatio n b d 3 7 5 1 3 f s - e 2 part n umber package fs: ssop - a2 0 packaging and forming specification e2: embossed tape and reel marking diagram ssop - a20(top view) BD37513FS part number marking lot number 1pin mark
BD37513FS 25 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 physical dimension , tape and reel information package na me ssop - a20 (unit : mm) pkg : ssop - a20 drawing no. : ex132 - 5001 (max 9.05 (include.burr))
BD37513FS 26 / 26 tsz02201 - 0c2c0e100430 - 1 - 2 ? 20 1 5 rohm co., ltd. all rights reserved. www.rohm.com tsz22111 15 001 16.dec.2015 rev.001 revision history date revision changes 16.dec .2015 001 new release
datasheet d a t a s h e e t notice-pga-e rev.00 2 ? 2015 rohm co., ltd. all rights reserved. notice precaution on using rohm products 1. our products are designed and manufac tured for application in ordinary elec tronic equipments (such as av equipment, oa equipment, telecommunication equipment, home electroni c appliances, amusement equipment, etc.). if you intend to use our products in devices requiring ex tremely high reliability (such as medical equipment (note 1) , transport equipment, traffic equipment, aircraft/spacecra ft, nuclear power controllers, fuel c ontrollers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (?specific applications?), please consult with the rohm sale s representative in advance. unless otherwise agreed in writing by rohm in advance, ro hm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ro hm?s products for specific applications. (note1) medical equipment classification of the specific applications japan usa eu china class class class b class class class 2. rohm designs and manufactures its products subject to strict quality control system. however, semiconductor products can fail or malfunction at a certain rate. please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe desi gn against the physical injury, damage to any property, which a failure or malfunction of our products may cause. the following are examples of safety measures: [a] installation of protection circuits or other protective devices to improve system safety [b] installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. our products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditio ns, as exemplified below. accordin gly, rohm shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of an y rohm?s products under any special or extraordinary environments or conditions. if you intend to use our products under any special or extraordinary environments or conditions (as exemplified bel ow), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] use of our products in any types of liquid, incl uding water, oils, chemicals, and organic solvents [b] use of our products outdoors or in places where the products are exposed to direct sunlight or dust [c] use of our products in places where the products ar e exposed to sea wind or corrosive gases, including cl 2 , h 2 s, nh 3 , so 2 , and no 2 [d] use of our products in places where the products are exposed to static electricity or electromagnetic waves [e] use of our products in proximity to heat-producing components, plastic cords, or other flammable items [f] sealing or coating our products with resin or other coating materials [g] use of our products without cleaning residue of flux (ev en if you use no-clean type fluxes, cleaning residue of flux is recommended); or washing our products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] use of the products in places subject to dew condensation 4. the products are not subjec t to radiation-proof design. 5. please verify and confirm characteristics of the final or mounted products in using the products. 6. in particular, if a transient load (a large amount of load applied in a short per iod of time, such as pulse. is applied, confirmation of performance characteristics after on-boar d mounting is strongly recomm ended. avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading c ondition may negatively affect product performance and reliability. 7. de-rate power dissipation depending on ambient temperatur e. when used in sealed area, c onfirm that it is the use in the range that does not exceed t he maximum junction temperature. 8. confirm that operation temperat ure is within the specified range descr ibed in the product specification. 9. rohm shall not be in any way responsible or liable for fa ilure induced under deviant condi tion from what is defined in this document. precaution for mounting / circuit board design 1. when a highly active halogenous (chlori ne, bromine, etc.) flux is used, the resi due of flux may negatively affect product performance and reliability. 2. in principle, the reflow soldering method must be us ed on a surface-mount products, the flow soldering method must be used on a through hole mount products. if the flow sol dering method is preferred on a surface-mount products, please consult with the rohm representative in advance. for details, please refer to rohm mounting specification
datasheet d a t a s h e e t notice-pga-e rev.00 2 ? 2015 rohm co., ltd. all rights reserved. precautions regarding application examples and external circuits 1. if change is made to the constant of an external circuit, pl ease allow a sufficient margin c onsidering variations of the characteristics of the products and external components, including transient characteri stics, as well as static characteristics. 2. you agree that application notes, re ference designs, and associated data and in formation contained in this document are presented only as guidance for products use. theref ore, in case you use such information, you are solely responsible for it and you must exercise your own indepen dent verification and judgment in the use of such information contained in this document. rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. precaution for electrostatic this product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. please take proper caution in your manufacturing process and storage so that voltage exceeding t he products maximum rating will not be applied to products. please take special care under dry condit ion (e.g. grounding of human body / equipment / solder iron, isolation from charged objects, se tting of ionizer, friction prevention and temperature / humidity control). precaution for storage / transportation 1. product performance and soldered connections may deteriora te if the products are stor ed in the places where: [a] the products are exposed to sea winds or corros ive gases, including cl2, h2s, nh3, so2, and no2 [b] the temperature or humidity exceeds those recommended by rohm [c] the products are exposed to di rect sunshine or condensation [d] the products are exposed to high electrostatic 2. even under rohm recommended storage c ondition, solderability of products out of recommended storage time period may be degraded. it is strongly recommended to confirm sol derability before using products of which storage time is exceeding the recommended storage time period. 3. store / transport cartons in the co rrect direction, which is indicated on a carton with a symbol. otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. use products within the specified time after opening a hum idity barrier bag. baking is required before using products of which storage time is exceeding the recommended storage time period. precaution for product label qr code printed on rohm products label is for rohm?s internal use only. precaution for disposition when disposing products please dispose them proper ly using an authorized industry waste company. precaution for foreign exchange and foreign trade act since concerned goods might be fallen under listed items of export control prescribed by foreign exchange and foreign trade act, please consult with rohm in case of export. precaution regarding intellectual property rights 1. all information and data including but not limited to application example contain ed in this document is for reference only. rohm does not warrant that foregoi ng information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. rohm shall not have any obligations where the claims, actions or demands arising from the co mbination of the products with other articles such as components, circui ts, systems or external equipment (including software). 3. no license, expressly or implied, is granted hereby under any intellectual property rights or other rights of rohm or any third parties with respect to the products or the informati on contained in this document. pr ovided, however, that rohm will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the produc ts, subject to the terms and conditions herein. other precaution 1. this document may not be reprinted or reproduced, in whol e or in part, without prior written consent of rohm. 2. the products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of rohm. 3. in no event shall you use in any wa y whatsoever the products and the related technical information contained in the products or this document for any military purposes, incl uding but not limited to, the development of mass-destruction weapons. 4. the proper names of companies or products described in this document are trademarks or registered trademarks of rohm, its affiliated companies or third parties.
datasheet datasheet notice ? we rev.001 ? 2015 rohm co., ltd. all rights reserved. general precaution 1. before you use our pro ducts, you are requested to care fully read this document and fully understand its contents. rohm shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny rohms products against warning, caution or note contained in this document. 2. all information contained in this docume nt is current as of the issuing date and subj ec t to change without any prior notice. before purchasing or using rohms products, please confirm the la test information with a rohm sale s representative. 3. the information contained in this doc ument is provi ded on an as is basis and rohm does not warrant that all information contained in this document is accurate an d/or error-free. rohm shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information.
datasheet part number BD37513FS package ssop-a20 unit quantity 2000 minimum package quantity 2000 packing type taping constitution materials list inquiry rohs yes BD37513FS - web page distribution inventory

▲Up To Search▲

Price & Availability of BD37513FS

	To Download BD37513FS Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .